How to Brew Loose Leaf Tea Posted: 01 Dec 2019 12:00 AM PST All you really need to prepare loose leaf tea is hot water, the leaves themselves, and a tea strainer. However, each type of tea requires slightly different steeping techniques. For the best cup, follow the recommended measurements, water temperature, and steeping time outlined on the package of tea. Experiment with different quantities of tea or steeping durations. Finally, add in your favorite sweetener or milk for a soothing cup of tea that really hits the spot. [Edit]Mastering Tea-Steeping Basics - Pour fresh, cold water into a saucepan or kettle. Don't use distilled or previously boiled water as it may negatively affect the taste of your tea. Instead, start with fresh, cool water from the tap.[1] Use an electric kettle, stovetop kettle, or a saucepan to warm up the water.
- If your local water is especially hard (i.e. high in mineral content), consider using bottled water for a more pleasant taste.
- Heat the water until it reaches . Remove the water from its heat source once it begins to steam, simmer, or reach a rolling boil. Depending on the tea variety you're preparing, you may need it to be slightly warmer or cooler to bring out the best flavors in the leaves. Use an instant-read thermometer to get the most accurate temperature.
- If you prefer, you can boil the water and allow it to cool down to the correct temperature before adding it to the tea leaves.[2]
- In general, white and green teas can be brewed at a lower temperature with the water just starting to steam, while oolong tea is typically best prepared at a moderate simmering temperature. Black and Puerh teas can withstand a higher temperature when the water hits a rolling boil.[3]
- Weight out 2 to 3 grams of loose leaf tea for every of water. Since tea leaves come in different shapes and sizes, it's best to measure out your tea by weight (i.e. grams) rather than by volume.[4] But if you do measure by volume, start with roughly 1 teaspoon for smaller leaves and about 1 tablespoon for larger leaves. Spoon out your desired amount of tea into a tea strainer or teapot, depending on how you plan to steep it.
- A teacup holds about of water, but since most coffee mugs hold about of water, you may need to double the amount of loose leaf tea you use in a larger mug.
- The amount of tea you decide to use is completely a matter of taste. Steep more or less to see which flavor you prefer.[5]
- Steep the tea in hot water for 3 to 5 minutes. Pour the hot water directly over the tea leaves and allow the flavors to seep out for a few minutes. Different tea varieties require slightly different steeping times, so be sure to follow the instructions on the packaging. If you're not sure how long to steep the leaves, start with 3 minutes for your first cup. Then add 30 more seconds for each subsequent cup until you find the perfect taste.
- Generally speaking, green and oolong teas can be steeped for about 3 minutes, white tea for 4 minutes, and black and Puerh teas for 5 minutes.[6]
- Avoid steeping tea longer than 5 minutes; it will only taste bitter. If you want a stronger cup, just add more tea leaves and keep the timing the same.
- Since herbal teas don't contain any actual tea leaves, they can often be left to steep longer without taking on a bitter flavor.[7]
- Remove the tea leaves from the water once they've steeped. How you do this will depend on the type of strainer you're using. Basket-style strainers, metal or silicone infusers, and filter bags can be lifted out of your teapot or cup to stop the infusion. Place the strainer on a spoon rest or saucer to catch the drips from the soggy tea leaves.
- If you steeped the tea directly in the teapot, hold a strainer over your teacup to catch the damp leaves as you pour out the tea.
- Discard the used tea leaves while they're damp, or wait until they've dried out to more easily tip them out of the strainer.
[Edit]Using Tea Strainers - Place the tea leaves directly into a tea strainer for easy cleanup. Place a basket-style tea strainer into a cup or teapot first. Measure out the loose leaf tea into the strainer and pour the hot water directly over it. Make sure you completely cover the tea leaves with water so that they steep properly.[8]
- After a period of 3 to 5 minutes, simply remove the strainer and the damp tea leaves.
- Choose a disposable filter bag for fine, powdery teas. Buy a packet of disposable tea filter bags from a tea shop or grocery store. Use one when you're preparing especially fine tea which tends to slip through mesh strainers easily. Keep the bag upright with the opening well above the water level so the tea leaves don't float out.
- You can also use a filter bag if you just want to make 1 cup at a time with easy cleanup.
- Use a mesh, basket-style tea strainer for larger tea leaves. Most loose leaf teas can be successfully steeped in these types of strainers. Choose one that fits correctly within the opening of the cup or teapot you'll be using; it shouldn't shift around or sink into the vessel, otherwise the tea leaves will escape.[9]
- Try a travel tea mug with a built-in basket strainer if you'll be on the go. Just remember to remove the tea after it's steeped for 3 to 5 minutes.
- While a short or rounded basket strainer may work for a single cup, use a deeper basket to steep loose leaf tea in a deep mug or teapot.
- Avoid using tea balls or infusers for large or fine leaves. Metal tea balls and silicone tea strainers are popular since they come in playful designs, but keep in mind the limited practicality of these tools. Refrain from using them for large-leafed tea as they won't leave much room for the leaves to unfurl as they become hydrated. Additionally, avoid using a tea ball or infuser for fine, powdery teas as the tea leaves may slip through the holes easily.
- If you're steeping medium-sized tea leaves in small quantities of water, a tea ball or infuser might not pose any problems.
- Hinged tea balls are difficult to fill and the mechanisms can be tricky to open and close, especially when the metal is hot.[10]
- Leave plenty of room for the tea leaves to expand in the strainer. Loose leaf tea leaves can grow up to 5 times their original size once you hydrate them with hot water. For this reason, aim to leave plenty of space in the tea strainer or filter bag. Don't overfill it with too much tea.[11]
- A mesh basket-style strainer will allow the tea to expand, while a tea ball may compress the leaves.[12]
- A little extra space will allow the water to flow around the tea leaves so you'll have a better result.
- Strain the tea after it steeps in the teapot if you prefer. This is a useful technique if you don't have a tea strainer that fits correctly in your teapot. Instead of placing the leaves into a strainer, what you can do is measure out the tea leaves and drop them directly into your teapot. After the leaves have steeped, hold a tea strainer over your cup. Carefully pour the liquid into the cup and you'll see the strainer catch the leaves.[13]
- Since there will still be leaves sitting in the teapot, the tea will grow more bitter as it continues steeping.
- To keep the tea warmer for a longer period of time, pre-warm your teapot or cup by sloshing some boiling water around inside it. Tip this out before adding the tea and the rest of the heated water.[14] Alternatively, try covering the teapot with a quilted tea cozy to keep it warm.
- Delicate green and white teas are best consumed immediately while more robust black teas can be enjoyed for a longer period of time.[15]
- After you've poured the tea into your cup, add milk, honey, lemon, or sugar to taste. Just avoid adding milk and lemon at the same time as the milk may curdle.
- When you start making a certain type of tea, it helps to use a thermometer to gauge the temperature of the water. Once you know how much steam and how many bubbles the water will give off at the optimal temperature, feel free to eyeball it.
[Edit]Things You'll Need - Kettle or saucepan
- Cool, fresh water
- Teapot
- Teacup
- Tea strainer
- Loose leaf tea
- Measuring scale or spoon
[Edit]Related wikiHows [Edit]References [Edit]Quick Summary |
How to Decorate a Christmas Tree Posted: 30 Nov 2019 04:00 PM PST A decorated Christmas tree makes for a very jolly home during the holidays. Make your home festive by following these easy steps. [Edit]Putting the Lights on your Tree - Test your Christmas lights before you hang them on your tree. Plug your Christmas lights into an outlet. Ensure that you don't have any burnt-out bulbs.
- Put lights on your tree. Make sure to do this before putting ornaments on your tree. LED lights are best for live trees as they do not heat up too quickly.[1]
- The Around-and-Around Wrap: Wrap strands of lights around the top of the tree and work your way down to the base of the tree. For a 6-foot tall tree, you will need about 6 strands of lights with 100 bulbs each.[2]
- Put your first light at the very top of the tree to begin. This light will shine on the star, angel, or snowflake that you will add later.
- Secure your light strands by weaving them in an out of the tree's branches.
- The Vertical Wrap: Divide your tree into 3 sections. Each section will have its own lights.
- Begin at the base of the tree and weave the lights up through the branches to the top of the tree and back down to the base. Repeat.
- Connect your light strands to an extension cord and plug it into a nearby outlet.
[Edit]Hanging the Ornaments on your Tree - Wrap the base of the tree in plastic. The plastic will collect any needles that fall off your tree. Cover the plastic with a festive Christmas tree skirt.
- These skirts add to the beauty of your tree and also keep the tree's needles from collecting on your floor.
- Hang your ornaments on the tree. Look for branches that are wider apart so that your ornaments won't rest on lower branches.
- Hang heavier ornaments further up on branches, closer to the trunk of the tree. The tree is strongest near the trunk and can bear more weight.
- Hang ornaments near lights to highlight certain ornaments. This works particularly well with shiny bulb, glass, or metal ornaments as these types are the most reflective.
- Spread ornaments evenly throughout the tree. Make sure not to hang too many ornaments on each branch.
- If a branch starts to get too weighed down, ornaments could fall off or the branch could break.
- Add additional decorations. These extras can include bows, strands of popcorn and cranberries, and candy canes.
- Add tinsel (optional). Tinsel makes your tree glitter. Hang tinsel near lights for the shiniest look possible.
- Be mindful with the amount of tinsel you place on your tree. Too much tinsel could take away from the beauty of your ornaments.
- For a more modern look, buy colored tinsel rather than the traditional gold and silver.
- Add the star (or decoration you wish to have at the top of your tree.) Make sure that it is secure and not crooked.
- Turn off the lights in your house. Admire the festive tree you have created and be jolly.
[Edit]Gathering Ideas for Themed Christmas Trees - Create a traditional look with solid red, white, silver and gold orbs. The orbs can be glass or plastic.[3]
- Add fake winterberries and silver bells to complete a traditional tree.
- Place silk flowers throughout your tree for a blooming theme. Hang white lights instead of colored lights to accent the flowers.[4]
- Silk roses, magnolias, and hydrangeas are good options for a wintery feel.
- Add richly colored ribbons and little silver orbs or glittering glass ornaments for a twinkling, flowery look.
- Create a nature-inspired look with rustic metal or glass ornaments. Place pine cones throughout the tree.[5]
- Mix bird ornaments in with fake leaves.
- White lights are best for this natural look.
- Hang red, white, and blue ornaments for a patriotic look. Mix glass and plastic ornaments alongside white lights for a tree that could rival the White House's own.[6]
- To get even more patriotic, hang red, white, and blue lights on your tree.
- Hang large, brightly colored orbs for a more modern look. Mod colors include lime greens, purples, bright blues, and hot pink.[7]
- Light strands with large light bulbs mixed with bright small and large ornaments will give your tree a contemporary, edgy feel.
- When buying a live Christmas tree, look for trees that have even branches all the way around. Avoid trees with large bald spots where no branches are growing because you will be able to hang less ornaments (and it will look awkward.)
- Craft stores such as Hobby Lobby may have different ornaments that you may like to add to your tree.
- Pick colors that complement each other. Blue and silver, red and gold, silver and gold, and purple, gold, and silver, are some color combinations that look great. Combinations like blue and pink, pink and gold, and red and blue may not look work as well on your Christmas tree.
[Edit]Warnings - Never hang candles on the tree as they are dangerous and can cause a fire.
- Do not overload the power outlets! This is a common occurrence at Christmas time and can lead to a fire.
- Make sure you turn off incandescent lights before you go to bed, especially on a live tree. You can unplug the lights or use a timer.
- Be careful with broken ornaments. The shards can be very sharp. It is best not to use glass decorations on a tree if you have pets or young children who could break them and get cut.
[Edit]Things You'll Need - Christmas tree (live or fake)
- Christmas tree stand
- Small plastic tarp
- Tree skirt
- Ornaments
- Strings of lights
- Beads and extra decorations (optional)
- Bows (optional)
- Star or other topper to place on the top of the tree.
[Edit]Related wikiHows [Edit]References [Edit]Quick Summary |
How to Fix Leaking Pipes Posted: 30 Nov 2019 08:00 AM PST Leaking pipes can cause a lot of damage to your home if they're left untreated. There are many temporary fixes for leaking pipes you can use, such as epoxy putty or pipe clamps, while you wait for a plumber. If you want to fix the pipe yourself so it's up to code, you can use a slip coupling to make the process easy. No matter what you use, be sure to turn off your water supply so your pipes don't leak while you're working! [Edit]Turning off Your Water Supply - Shut off the water supply to your home. Locate your main water supply, which is typically in your basement or crawl space. Turn the dial clockwise to shut off the water going into your home so the leak stops and doesn't cause more damage.[1]
- In an emergency, call your water company and see if they can shut off the water leading to your home.
- Turn on the faucets connected to the pipe to drain them. Start by turning on the lowest faucet in your home, such as an outdoor hose pipe or a sink in the basement. Let the water run until the pipe is completely empty. If the leak is on a pipe leading to a specific fixture, then turn on that faucet to drain it.[2]
- Dry the leaking area on the pipe. Once all of the water is drained from the pipes, use a cleaning cloth to wipe the area around the leak completely dry. That way it won't be slippery while you're trying to work on it.[3]
- Set a cloth or bucket underneath the leak in case any stray drops of water come out of the leak.
[Edit]Applying Epoxy Putty for a Temporary Fix - Put on latex or nitrile gloves. Epoxy putty heats up while you're working with it and could cause pain on bare skin. Make sure the gloves are thin enough where you can still work intricately. Wear the gloves any time you handle the epoxy putty.[4]
- You can buy latex or nitrile gloves from any hardware or big box store.
- Mix plumbing epoxy putty by hand to combine it. Rip off a small ball of epoxy putty from the tube and knead it together between your fingers. The darker epoxy will mix with the lighter exterior to activate it. Once the putty has a consistent light grey color, you can stop kneading it.[5]
- You can buy plumbing epoxy putty from your local hardware store.
- Wrap the putty around the leaky area. Mold the putty around the leak on your pipe so it wraps completely around it. Make sure the putty forms a layer that's about thick around the leak so it holds in place. Taper the edges of the putty onto the pipe so it makes a watertight seal.[6]
- Epoxy putty works on straight lengths of pipes as well as joints.
- Let the putty set for 5-10 minutes before turning your water on. Once the epoxy putty is mixed, it will set quickly so you can use your water again. Leave the putty alone for at least 5 minutes while it sets so it can solidify. Once the epoxy sets, you can turn your water back on.[7]
- Epoxy putty is a temporary fix, so be sure to fully replace your pipe or contact a plumber the next day.
[Edit]Clamping Small Leaks - Buy a pipe clamp that's the same size as the leaky pipe. Pipe clamps use rubber gaskets create a tight seal to secure a small leak on your pipe. You can purchase these in the plumbing section of your local hardware store, but make sure to buy a pipe clamp that is the same size and at least as long as the pipe that's leaking so you have a tight fit when you secure it.[8]
- Align the rubber gasket on the pipe with the leak. The rubber gasket is the rectangular piece inside of the clamp that makes your pipe's water-tight. Set the rubber gasket on top of the hole in your pipe so it seals the leak completely. If the leak is on the bottom of the pipe, hold the clamp in place until you secure the clamp.[9]
- Fit the clamp around the gasket and tighten the bolts. Close the clamp around your pipe so it fits tightly on it and feed the bolts provided with the clamp through the holes. Turn the nuts using a wrench to secure them to the bottom of the bolts. Continue tightening the bolts until the clamp stays in place and doesn't turn any further.[10]
[Edit]Putting a Slip Coupling on Your Pipe - Get a slip coupling that matches the size and type of your pipe. Slip couplings are small, watertight connections that connect 2 different pieces of pipe. Look for a slip coupling has the same diameter as the pipe you need to fix and is long enough so you can cut out the leak. Before you purchase one, make sure the coupling is the same material as your pipe, such as PVC or copper.
- You can buy slip couplings from your local hardware store.
- Slip couplings can be a permanent solution to fixing your pipes and they are up to code.
- Mark the length of the slip coupling on your pipe. Hold the slip coupling up to the leaky spot on your pipe so the coupling extends out from each side. Use a marker to draw a line on your pipe at the end of the slip coupling. This will help ensure that you cut out the right length of pipe so the coupling can still fit.[11]
- Use a pipe cutter to cut out the leaky area on the pipe. Pipe cutters are small devices that easily slice through a pipe as you rotate them around. Set the edge of your pipe cutter inside the line you drew and tighten the screw on the bottom of the device. Rotate the pipe cutter around the pipe completely and tighten the screw again. Keep spinning and tightening the pipe cutter until it makes a clean cut through the pipe. Repeat the process in from the other line you drew.[12]
- You can buy pipe cutters from your local hardware store.
- Pipe cutters work on metal and PVC pipes.
- Some PVC pipe cutters look like a pair of scissors. Put the blade over the pipe and slowly squeeze the cutters shut.
- Scrape the inside and outside of the pipe with a deburring tool. A deburring tool is a special tool used to scrape the inside and outside of the pipe to help reshape it after you make your cut. Hold the pipe steady with your nondominant hand and set the blade edge of the deburring tool inside the pipe. Scrape around the inside edge of the pipe with your tool to deburr it. The take the tool out of the pipe and scrape the outside edge.[13]
- You can buy deburring tools in the plumbing section of a hardware store.
- Make sure you deburr both sides of the cut pipe to prevent future leaks.
- Slide the slip coupling onto the ends of your pipe. Take your coupling and slide an end over one side of your pipe. Push the coupling on far enough so you're able to line it up with the other side of the cut pipe. Line up the other end of the coupling with the pipe and pull it over so the 2 pipes are connected by the coupling. The coupling will hold the pipes together so water can flow between them.[14]
- Some couplings may make you tighten them by hand or with a wrench. Follow the directions on the packaging carefully to see if there are any additional steps.
[Edit]Warnings - Contact a plumber if you don't feel comfortable cutting or replacing your own pipes or if the leak is difficult to reach.
[Edit]Things You'll Need [Edit]Applying Epoxy Putty for a Temporary Fix - Latex or nitrile gloves
- Epoxy putty
[Edit]Clamping the Leak Shut [Edit]Putting a Coupling on Your Pipe - Pipe slip coupling
- Pipe cutter
- Measuring tape
- Deburring tool
[Edit]Related wikiHows [Edit]References [Edit]Quick Summary |
nice
ResponderExcluirthanks and cheers
Geotextile Woven Harga